断后延伸率 指金属材料受外力(拉力)作用断裂时,试棒伸长的长度与原来长度的百分比。 检测标准 ASTM E8/E8M-2011 金属材料抗拉试验方法 Standard Test Methods for Tension Testing of Metallic MaterialsASTM A370-2012 钢产品机械测试的试验方法及定义 Standard Test Methods and Definitions for Mechanical Testingof Steel Products BS EN ISO 6892-1-2009 金属材料.抗拉试验.*1部分:环境温度下的试验方法 Metallic materials — Tensile testing Part 1:Method of test at ambient temperature GB/T 228.1-2010 金属材料 拉伸试验 *1部分:室温试验方法 Metallic materials--Tensile testing--Part 1:Method oftest at room temperature JIS Z2241-2011 金属材料--拉伸测试--室温下的试验方法 Metallic materials -- Tensiletesting -- Method of test at room temperature AS 1391:2007 金属材料-常温拉伸试验 Metallicmaterials - Tensile testing at ambient temperature ASTM B557-2010 锻制和铸造的铝及镁合金制品的拉力试验方法 Standard Test Methods for Tension Testing Wrought and CastAluminum- and Magnesium-Alloy Products
在GB/T228—2002(金属材料室温拉伸试验方法)中,对断后伸长率的表示方法作了相应的修改,新标准用字母A代替旧符号的δ。试样标距分为比例标距和非比例标距两种,因而有比例试样和非比例试样之分。 1.比例试样凡试样标距与试样原始横截面积有以下关系的,称为比例标距,试样称为比例试样。 Lo=k(So)1/2 式中(k——比例系数So——原始横截面积) 2.非比例试样 非比例标距(也称定标距)与试样原始横截面积不存在上式关系。如果采用比例试样,应采用比例系数k=5.65的值,因为此值为*通用,除非采用此比例系数时不满足小标距15mm的要求。在必须采用其他比例系数的情况下,k=11.3的值为**采用。产品标准或协议可以规定采用非比例标距。不同的标距对试样的断后伸长率的测定影响明显。新、旧标准对于断后伸长率符号表示的差异如下表: GB/T228—2002 (新) GB/T228—1987(旧) 备注 A δ5试棒的标距等于5倍直径(短标距) A11.3 δ10 试棒的标距等于10倍直径(长标距) Axmm δxmm试棒的标距为定标距Xmm(定标距) 检测标准 1.线材、圆棒试样: d≥10mm,长度 L≥200mm3mm≤d≤10mm,长度 L≥200mm d≤3mm,长度 L≥1000mm(线材小300mm,棒材小80mm) 2.矩形试样: ≥16*200mm(L小120mm)3.管状试样: OD≤30mm, L≥300mm (小150)OD>30mm, 一般要求L≥300mm 另 OD≤55mm,可整管拉伸
金属材料发生屈服现象时的屈服**,亦即抵抗微量塑性变形的应力。对于无明显屈服的金属材料,规定以产生0.2%残余变形的应力值为其屈服**,称为条件屈服**或屈服强度。大于此**的外力作用,将会使零件失效,无法恢复。如低碳钢的屈服**为207MPa,当大于此**的外力作用之下,零件将会产生变形,小于这个的,零件还会恢复原来的样子。屈服强度检测标准 ASTM E8/E8M-2011 金属材料抗拉试验方法 Standard TestMethods for Tension Testing of Metallic Materials ASTM A370-2012 钢产品机械测试的试验方法及定义 Standard Test Methods and Definitions for Mechanical Testingof Steel Products BS EN ISO 6892-1-2009 金属材料.抗拉试验.*1部分:环境温度下的试验方法 Metallic materials — Tensile testing Part 1:Method of test at ambient temperature GB/T 228.1-2010 金属材料 拉伸试验 *1部分:室温试验方法 Metallic materials--Tensile testing--Part 1:Method oftest at room temperature JIS Z2241-2011 金属材料--拉伸测试--室温下的试验方法 Metallic materials -- Tensiletesting -- Method of test at room temperature AS 1391:2007 金属材料-常温拉伸试验 Metallicmaterials - Tensile testing at ambient temperature ASTM B557-2010 锻制和铸造的铝及镁合金制品的拉力试验方法 Standard Test Methods for Tension Testing Wrought and CastAluminum- and Magnesium-Alloy Products