SKF旗下LINCOLN林肯润滑系统，034550，034562，034568，034572
SKF润滑泵, SKF润滑, 034550 ORINGS
SKF Lincoln 林肯润滑系统
034550 O RINGS
034562 U CUP SEAL
034568 U CUP PACKING
034572 O RING
034700 O RING
034701 U CUP PKG
034703 U CUP PKG
034704 U CUP PKG
034708 O RING
034709 O RING
034710 U CUP PKG
034711 O RING
034712 O RING
034770 O RING
034778 TETRSEAL PACKING
034793 GASKET
034802 PLUNGER PACKING
034837 PACKING
035007 STEM PACKING
035073 PACKING
035095 SWIVEL PACKING
035135 GLAND PACKING
036043 V PACKING (SET OF 4)
036044 V-PACKING
036045 V PACKING
036046 VEE PACKING
038069 VEE PACKING
038070 PISTON PACKING
038077 GASKET
038095 PACKING
038129 PISTON RING
038154 U CUP PACKING
038155 U CUP PACKING
038157 WEAR RING
038158 WEAR RING
038162 VALVE SEAT GASKET
038165 U CUP
040409 BODY CASTING
040426 COVER BODY
040492 FOLLOWER CASTING
040524 CYLINDER HEAD
040537 OUTLET BODY
040616 PISTON
040782 CYLINDER HEAD
040783 LOWER CYL HEAD
040799 SUPPORT CASTING
040813 FOLLOWER CASTING
041228 WASHER
041230 VALVE BODY
045605 GUIDE PLATE
045744 TOGGLE
045788 HANDLE
045826 GUIDE WASHER
045923 CLIP
045924 CLIP
045924-9 CLIP SS
045926 CLIP
045926-9 CLIP SS
045936 COVER CAP
045980 SPRING RET
046007 DRUM COVER ASM
048039 PACKING WASHER
048206 PACKING WASHER
048209 PISTON WASHER
048210 PISTON WASHER
048212 PISTON WASHER
048213 PACKING WASHER
048216 PACKING WASHER
048217 PACKING WASHER
048218 PACKING WASHER
048237 PACKING WASHER
048263 PACKING WASHER
048264 THRUST WASHER
048265 WASHER
048268 WASHER
048375 WASHER
048377 WASHER
048379 WASHER
048382 WASHER
048417 WASHER OF FOLLOWER
048436 WASHER
048448 WASHER
048462 WASHER
048467 WASHER
048468 WASHER
048473 WASHER
048487 WASHER
048490 PACKING RETAINER
048490-8 PACKING RETAINER
048599 RET WASHER
048603 WASHER
048604 WASHER
048614 WASHER
048620 WASHER
050000 HEAD SCREWS
050015 SCREWS
050030 SCREWS
050051 HEX HD CAP SCREW
050060 SCREW , HEX. HD. ,1/4"-20
050076 SCREW
间隙性空信号的运作原理
间隙性空信号是无接触式运作的，并且主要由以下部件组成：容器底部固定的磁力开关
(I)搅拌桨相连的可动导板 (II) 带有一个磁铁 (III) 和一个控制凸轮(IV)如果容器加注了适合间歇性空信号功能的润滑脂，泵机运行时，导板 (II) 就会因为润滑脂的阻力而偏转。与导板 (II)相连的磁铁 (III) 在其内部环形轨道上运行，而不会触发磁力开关 (I) 上的脉冲。每次旋转时，控制凸轮 (IV)都引导磁铁与可旋转的导板一起向外。在离开控制凸轮后，润滑脂的阻力又重新按压导板和磁铁向内。如果容器内的润滑剂下降到一定程度，以至于润滑脂的阻力不再足以使导板(II) 偏转，磁铁 (III) 就会保持在外轨道，并且每次旋转都会触发其磁力开关 (I) 一次脉冲。如果磁铁 (III)在一个作业周期内运动经过磁力开关 (I) 6 次，将会直接在泵机的信号接口上发出空信号。要对泵机的外部控制装置进行编程